![Correct abbreviation for igrade](https://loka.nahovitsyn.com/160.jpg)
![xmos xscope xmos xscope](https://www.all-electronics.de/files/upload/post/all/wp-content/uploads/migrated/image/artikel/28362_3.jpg)
5.1 XCore: Connecting a WiFi sliceCARD to xCORE-200 eXplorerKIT?.5 Notes 3: WiFi sliceCARD via PCIe/GPIO?.Take a chanend which assumes a physical index on the row/column indexing scheme and convert it to the real chanend.
#XMOS XSCOPE CODE#
Steve needs to supply code for bringing up link on Swallow and link on peripheral board and program peripheral routing tables.xn file must include the XSCOPE entry of connected core ID, as shown in the example. In order to get the network generated, this. xn file in the etherboot code "Swallow-Ethernet-v2" code: the. Program it seperately and give it this id. You can also look at swallow-mcsc.py and see how the code it generates uses them. These are found in sc_swallow_communication you will find some stuff in ledtest.xc in tool_xmp16_manycore/code that uses them. Similarly, swallow_cvt_chanend() is used by the mcsc script to generate channel addresses then convert the top 16-bits into the real node ID. 5) and turn it into a node ID appropriate for the grid you're running on (yes, it's a runtime thing). Swallow_id() will take a core index (e.g. Purpose | Is Xscope | Row | Col | Layer | Is Peripheral Row: Most extreme North is row 0, then proceeds south with +1 per rowĬolumn: Most extreme West is column 0, then proceeds East with +4 per column Sw_swallow_etherboot/app_swallow_etherboot/src/swallow_etherboot_conf.h* Calculating NodeIDs The etherboot code is available on github: is a Makefile included, but *before Making etherboot.xe, one needs to set the board configuration in: The resulting binary is etherboot.xe and need only be compiled once for each Swallow topology. The Etherboot slice runs a standard single-core XE binary, using the standard XMOS toolchain. To do this, a single wire must be connected between pin GPIO1 (top pin of P13) on the Etherboot board and pin 15 of the XTAG2 header on the top-left most Swallow slice in the array (pin 15 is the 8th pin up from the arrow marked '1' on P5).Īn XTAG2 is connected to the Etherboot module to allow programming and I/O, and an ethernet XSlice is added to the PCIe header on the Etherboot board.Īn ethernet cable is then connected to a host PC, as well as the USB connection of the XTAG2. It is always added to the S2 connection of the bottom-right Swallow slice (when their topology is visualised as a 2D grid).Ī global reset connection must also be added to the Swallow boards to allow the Etherboot module to reset before programming. The Etherboot board connects to the Swallow network. Swallow slices do not have built-in Ethernet support, so Ethernet connectivity is provided by the addition of a peripheral "Etherboot" board. The conventional JTAG connection is not required, except for the connection of a global reset signal. Ethernet can also be used to stream in and stream out run-time data. The Swallow tools program Swallow systems over Ethernet. Programming and tracing Quick start instructions to program Swallow Overview sgb (Swallow Grid Binary) file, which can be immediately downloaded to the Swallow system. The various tools are discussed later in this page, but the output is a single. The main file must contain the line #define MCMAIN.The main function must be declared in a separate file to the remainder of the code (any number of source files are supported).The key differences in using the tools are: The Swallow tools are based on the XMOS tool chain, but re-implement the compilation front end, linking and output to a custom "multi-core binary" format. They cannot support non-rectangular topologies.įor these reasons, we have created a custom tool-chain, the Swallow tools.All debug via JTAG, which has a massive slowdown effect on the system.Compile times in the order of minutes for even a single board.A hard-coded limit of ~100 processors, limiting us to a maximum of 6 Swallow slices.However, there are several major drawbacks to using the tool chain, including: The standard XMOS tools are capable of compiling, debugging and analysing multi-core programs and they can be used with Swallow boards. There are two separate tool chains that are compatible with Swallow:
![Correct abbreviation for igrade](https://loka.nahovitsyn.com/160.jpg)